Site-to-site VPN

Add a how-to article to your user guide

How-to articles describe steps for completing an end-user task. To add a new how-to article, follow these steps:

Select a topic you want to add the how-to under
Click on new page at the top of the page
Select how-to

Reference articles

Automatic NAT Traversal for IPsec Tunneling between Cisco Meraki Peers: Automatic NAT traversal is the default method used to establish a secure IPsec tunnel between Cisco Meraki VPN peers. This method relies on the Cloud to broker connections between remote peers automatically. It is the preferred method because it works well even when peers are located on different private networks protected by a firewall and NAT.
Cisco ASA Site-to-site VPN with MX Series: This article outlines configuration steps, on a Cisco ASA, to configure a site-to-site VPN tunnel with a Cisco Meraki MX or Z1.
Configuring Cisco 2811 router for Site-to-site VPN with MX Series Appliance using the Command Line Interface
Configuring Hub-and-spoke VPN Connections on the MX Security Appliance: Site-to-site VPN connections between MX Security Appliances and/or Z1 Teleworker Gateways will automatically form a mesh topology between all VPN-enabled peers in the same Dashboard organization by default. This is often undesirable because such connections establish unnecessary IPSec tunnels between remote sites and create performance-degrading networking overhead.
Configuring Site-to-site VPN between MX Appliances in Different Organizations: All MX security appliances within the same organization will be able to use our AutoVPN feature to establish a Site-to-site VPN between themselves. However, if two MX Security Appliances are in separate organizations, they will not be able to set up an automatic VPN. They must be configured as if they were non-Meraki peers. This article outlines the basic configuration steps necessary to establish a site-to-site VPN tunnel between MX devices in different organizations.
Configuring Site-to-site VPN over MPLS: Many enterprise networks have existing MPLS circuits that connect locations. However if the MPLS goes down, the connection to a remote location is lost. MX Security Appliances can be placed in these networks to dynamically fail over to a VPN connection via a secondary Internet connection.
Custom IPsec policies with Site-to-site VPN: When using a Cisco Meraki MX Security Appliance to create an IPsec VPN to a non-Meraki peer, multiple options are available for customizing the parameters of that VPN connection. For more information on site-to-site VPN functionality, please refer to our security appliance documentation. This article will specifically cover the options available when customizing IPsec parameters for a peer.
IPsec VPN Lifetimes: IPSec VPNs using IKE utilize lifetimes to control when a tunnel will need to re-establish. When these lifetimes are misconfigured an IPSec tunnel will still establish but will show connection loss when these timers expire. This article will cover these lifetimes and possible issues that may occur when they are not matched.
MX to Sonicwall Site-to-Site VPN Setup: When setting up a Site-to-Site VPN between an MX Security Appliance and a Sonicwall the following settings should be used on the Sonicwall to get the tunnel up and running.
Netgear Prosafe Site-to-site VPN with MX Series: The Netgear Prosafe can form a site-to-site VPN with a Meraki MX series security appliance. The easiest way to configure this is by logging onto your Netgear Prosafe via a web browser and clicking on the VPN Wizard found on the left hand side of the page under VPN. This will display text informing you that several defaults are assumed during the wizard and that these can be adjusted by clicking VPN Settings after the wizard has completed. Click the Next button to begin the configuration.
Site-to-Site VPN Failover Behavior: Failover is a feature built into the MX series to keep a constant connection in the event of Primary link failure. Failover occurs when the primary uplink of the MX is unable to reach the internet. The VPN connection of the MX always goes out the Primary interface, as configured under Security Appliance > Configure > Traffic shaping. In the event of primary link failure, the MX will tear down the existing VPN tunnel and attempt to negotiate a new tunnel with the remote VPN peer.
Site-to-site VPN Firewall Rule Behavior: Administrators have the ability to add firewall rules to restrict the traffic flow through the VPN tunnel for a Cisco Meraki MX Security Appliance. These firewall rules will apply to all MX networks in the organization that participate in the auto site-to-site VPN and 3rd party VPN endpoints.
Site-to-Site VPN Troubleshooting: Meraki Site-to-Site VPN makes it easy to connect remote networks and share network resources. In the event that VPN fails or network resources are inaccessible, there are several places to look in Dashboard to quickly resolve most problems. This article will overview common site-to-site VPN issues and recommended troubleshooting steps.
Small Remote or Home Office VPN Options: Cisco Meraki product lines offer various types of VPN options for small office and/or remote deployments. Each option is recommended for a different type of scenario, ranging from a single client, to several wired and wireless clients. If you have a complex requirement not covered below, please contact your Cisco Meraki account executive to discuss what would be the best fit for your particular needs.
Subnetting large-scale Z1 deployments for route summarization: When several Z1 Teleworker Gateways are deployed to establish Site-to-site VPN tunnels to an MX in Concentrator Mode, a static route for each VPN connection needs to be configured on the MX's default gateway. However, configuring one static route per device is inconvenient for large-scale Z1 deployments. Using Route Summarization, this task can be accomplished with one route if configured correctly.
Troubleshooting Automatic NAT Traversal for Meraki Auto VPN: Cisco Meraki VPN peers can use Automatic NAT Traversal to establish a secure IPsec tunnel through a firewall or NAT. When ACLs on an upstream firewall block source ports or more likely the case destination UDP ports in the range 32768-61000 on outbound traffic, a peer will not be able to punch a hole in the firewall and establish a tunnel with other remote peers.
Troubleshooting Non-Meraki Site-to-site VPN Peers: The MX Security Appliance provides the ability to configure VPN tunnels to third-party devices. This article describes third-party VPN considerations, required configuration settings, and how to troubleshoot third-party VPN connections.
Troubleshooting VPN Registration for Meraki Auto VPN: When using VPN functionality to securely tunnel traffic between Cisco Meraki devices, such as the MX Site-to-site VPN, or MR Teleworker VPN, the devices must first register with the Dashboard VPN registry. This allows their connections between each other to be dynamic, and automatically establish without manual configuration. However, sometimes issues can occur with this process, which will be discussed in this article.
Using OSPF to Advertise Remote VPN Subnets: Cisco Meraki MX security appliances support the OSPF routing protocol to advertise remote VPN subnets to neighboring layer 3 devices. This feature is useful in topologies where a large number of VPN subnets makes configuring static routes impractical. This article outlines the prerequisites and configuration necessary for OSPF on the MX platform.
Using Site-to-Site VPN Translation: Sometimes, remote devices connected via Site-to-site VPN use the same overlapping local subnets on their networks. When administrators try to connect overlapping subnets using Site-to-site VPN, devices will not be able to communicate with each other across the tunnel.
Watchguard XTM Site-to-site VPN with MX Series: The Watchguard XTM can form a site-to-site VPN with a Meraki MX series security appliance. To do this login in to Watchguard by connecting to its IP address via a web browser. On the left hand side click on VPN->Branch Office VPN. Under the Gateways tab click Add to give the gateway a name that will be meaningful to you and easy to remember.

对非 Meraki 站点到站点 VPN 对等点进行故障排除: MX 安全设备提供配置与非 Meraki 设备的连晋的 VPN 隧道配置的功能。本文介绍非 Meraki VPN 的注意事项、所需配置设置，以及如何对 MX 到非 Meraki VPN 的连接进行故障排除。

站点到站点 VPN 故障排除: 通过 Meraki 站点到站点 VPN 可轻松连接远程网络和共享网络资源。当 VPN 发生故障或网络资源不可访问时，查看“控制面板”中的多个位置可快速解决大多数问题。本文将概述常见的站点到站点 VPN 问题和推荐的故障排除步骤。

No articles with the article type topic could be found.

Most popular (views)

Highest rated (rating)

Recently added (date created)

Site-to-site VPN Settings
Meraki AutoVPN technology is a unique solution that allows site-to-site VPN tunnel creation with a s...
- 站点到站点 VPN 设定

VPN Status Page
The VPN Status page provides detailed, useful information about all VPN tunnels on your Meraki organ...

Site-to-site VPN

Table of contents

Add a how-to article to your user guide

Most popular (views)

Highest rated (rating)

Recently updated (date updated)

Recently added (date created)

Tags

Classifications

Explore the Product

Article ID

Explore Meraki

Contact Support

Ask the Community

Site-to-site VPN

Table of contents

Add a how-to article to your user guide

Most popular (views)

Highest rated (rating)

Recently updated (date updated)

Recently added (date created)

Related articles

Tags

Classifications

Explore the Product

Article ID

Explore Meraki

Contact Support

Ask the Community